Troubles configuring my hard drive to install windows 7?

Question

I recently replaced my 320GB Toshiba hard drive with a 500GB Hitachi hard drive on my Dell latitude E6410. I have tried deleting the reformatting the partitions, no luck
At the end of my attempt of installing windows 7 64bit, I get a message stating

"Windows setup could not configure windows to run on this computer's hardware".

It seems strange as my previous Toshiba hard drive installed windows 7 just fine. Could it be the difference of GB that is causing this problem?

I have read multiple sources on forums telling others to change the bios setting for the hard drive to SATA or IDE. My bios settings only had Legacy or UFEI settings. Tried both with no successes.

Any ideas of what could be the problem? Any help is greatly appreciated.

Answer 1

Hi David l,



I am Shaina from Dell Social Media Outreach Team,



In this case first of all please ensure that the new Hard drive is of the same configuration as the Original one.



Also check the status in BIOS to ensure Hard Drive is getting detected in the system.

Turn on the system and Tap F2 ( 8-10 times)

check what is written in front of hard drive

in front of Hard Drive (HDD) it should give hard drive specification.



Once this step is complete also update the BIOS To the latest version from the following link :



http://dell.to/106iKKR



1) Enter the Service Tag and press submit button. ( You can find the service tag at the bottom of the laptop on white sticker, it’s a seven digit

alphanumeric code which ends with BS or number 1.)

2) Click on Drivers and Downloads.

3) Choose the Operating system.

4) Click on BIOS option and download the latest driver.



( You will need to use the OLD HDD to Flash the BIOS , Connect the Old HDD to the system and then update the BIOS by logging into windows and restart your computer. Also ensure no other application is open while you install this and ensure to connect the adapter while updating the BIOS)



For further issues or assistance if you need kindly revert us on the same post I Would be more than happy to assist you.

We would recommend you do not post your private information on a public forum.

Thanks & Regards

Dell_Shaina_M

Dell Social Media Responder.



(You can now follow us on you tube for online video support http://dell.to/187A9Hj)

Answer 2

Within the BIOS, there is a place where you instruct the computer on how to use the SATA ports: IDE or AHCI This is what you probably need to change. Usually, there are some drill downs in the BIOS where you configure the peripherals and drives. Under one of them you should find something about the SATA. The SATA settings for the SATA ports will have to options I mention below/next to that.



Size of the drive should not be an issue with this laptop. It is new enough to understand the 500GB drive.

Answer 3

How do I know if I have this issue?

To determine whether your system is affected by this issue, follow these steps:1.Insert a Windows 7 or Windows Server 2008 R2 DVD into your DVD drive, and then close the drive.

2.Restart your computer, and then press a key on the keyboard when you receive the following message:





Press any key to boot from CD or DVD



3.Set the following preferences, and then click Next.◦Language to install

◦Time and currency format

◦Keyboard or input method



4.On the next screen, select Repair your computer.

5.In the System Recover Option dialog box, select the drive that you tried to install Windows 7 or Windows Server 2008 R2.

6.In the Choose a Recovery Tool box, select Command Prompt.

7.Change to the drive that you want to install Windows on. (In a standard installation, this is drive C.) Type Notepad, and then press ENTER.

8.In Notepad, click Open on the File menu, and then browse to %systemroot%\Panther.



Note On a standard installation to drive C, the path is C:\Windows\Panther. (On most PCs this will be the C:\Panther folder)

9.Open the file setuperr.log, and look for lines that resemble these:



2010-09-23 17:34:58, Error [0x0f0082] SYSPRP LaunchDll:Failure occurred while executing 'C:\Windows\System32\scecli.dll,SceSysPrep', returned error code 1208[gle=0x000003e5]

2010-09-23 17:34:59, Error [0x060435] IBS Callback_Specialize: An error occurred while either deciding if we need to specialize or while specializing; dwRet = 0x4b8



Note If these lines and errors exist, note the errors.



10.Open the setupact.log file that is located in the same directory, and then look for the line that resembles the following line:



2010-09-23 17:31:26, Info SYSPRP SPPNP: iaStorV is the function driver for device PCI\VEN_8086&DEV_2822&SUBSYS_2819103C&REV_02\3&33FD14CA&0&FA



Note If this line exists, it indicates that the drive on which you are trying to install Windows 7 or Windows Server 2008 R2 is configured in a RAID configuration.







Method 1: Download the appropriate drivers for your hard disk drive

Download and install the latest drivers for your Windows 7-based or Windows Server 2008 R2-based computer. To do this by using another computer, visit the following Intel website and download the appropriate drivers for your hard disk drive (either 32-bit or 64-bit) to a flash drive. Or, burn the drivers onto a CD or DVD. The flash drive or the disc will then be used during setup of Windows 7 or of Windows Server 2008 R2.



http://www.intel.com/support/chipsets/imsm/sb/CS-031502.htm



1.Go to another computer that has an internet connection and click the link below to download the driver for your hard disk drive (either 32-bit or 64-bit):



http://www.intel.com/support/chipsets/imsm/sb/CS-031502.htm







2.Save this downloaded driver to a DVD or USB flash drive or an external hard drive that can be taken to the PC that you're installing Windows to.

3.Next, start the installation of Windows 7 or Windows Server 2008 R2 and watch for the Load Driver option. You will see this option on the Where do you want to install Windows? screen in the lower right corner.

4.Connect the USB flash or external drive to the computerthat you're installing Windows or take the Windows DVD out of the drive and put the driver DVD into the drive. (You will put the Windows DVD back into that drive after the driver is loaded)

5.Click Load Driver, (clicking this option checks removable media for storage controller drivers)

6.Once the driver is loaded, continue with the Windows setup.

The Advanced Drive Format hard drive will be recognized and Setup will continue as expected.





Method 2: Change the BIOS hard disk drive setting to AHCI or IDE





Warning This procedure may involve changing your hard disk drive settings in the BIOS. Incorrect changes to the BIOS of your computer can result in serious problems. Microsoft cannot guarantee that problems that result from changes to the BIOS can be resolved. Change the BIOS settings at your own risk. Incorrect or corrupted BIOS settings can cause startup problems or shutdown problems.



You can change the hard disk drive setting in the BIOS to AHCI or to IDE if the hard disk drive setting is currently set to a RAID configuration. If you set the hard disk drive to AHCI or to IDE, you do not have to install the driver that you obtained in method 1.



Microsoft cannot provide specific instructions for how to change the BIOS settings because they are specific to your computer. For information about the correct BIOS settings for your computer and how to check and change these settings, see your computer documentation, or contact the manufacturer of your computer.





SORRY IF THIS DID NOT HELP :/

Answer 4

First, go into your BIOS and make sure that it is seeing the drive's full capacity.



If that's OK, try splitting the drive into two 250 GB partitions, and see if Win7 will install on one of those partitions.

Answer 5

do you create only one partition for the whole drive then don't delete it and live it unallocated then click next and try again to set it up cause windows 7 setup cd will create it automatically it might even create a small system hidden 100MB partition for booting!